Seamless gutter installation
Gutter Replacement in Omaha, NE
Some gutters reach a point where patching costs more each year than starting over. Rusted seams, sagging runs and downspouts in the wrong places are the usual signs that point you toward replacement.
- Phone answered 24/7
- Our own crews
- Measured and priced on site
Omaha, NebraskaQuick answer
Gutter replacement is a full tear-off of the old system followed by new seamless gutters and downspouts in the same visit. It makes sense when the gutters are rusting through, leaking at many joints, too small for the roof, or hung on fascia that has started to rot. Most Omaha homes are done in a single day.
Plenty of homeowners call us for a leak and end up asking a better question: is this gutter worth fixing at all? A single loose hanger or one dripping corner is a repair. A system that leaks at a dozen joints, has rust holes along the bottom and pulls away from the house in three places is not.
Replacement lets us correct everything at once. We pull the old metal, look at the wood it was hiding, fix what is soft, and put up a system sized for the roof you actually have. For smaller problems, our gutter repair service is the cheaper route, and we will tell you plainly which one your house needs.
Repair or replace: how we make the call
We start with the age and material. Galvanized steel gutters from the 1960s and 1970s tend to rust from the inside of the trough outward, and once you can poke a screwdriver through the bottom, patching only buys a season. Thin sectional aluminum with failed splices along every run is in the same category.
Then we look at fit. A gutter that overflows because it is undersized will keep overflowing no matter how many times it is resealed. If the roof sheds more water than a 5-inch trough and a few 2x3 downspouts can move, replacing with a larger system is the only real fix.
- Rust holes or thin spots in the trough bottom
- Leaks at more than a few joints
- Sections pulling loose from soft fascia
- Repeated overflow on the same runs
- Downspouts too few or too small for the roof
Tear-off and haul away
Old gutters come down section by section so we do not drag hangers through the shingles or gouge the siding. Spikes, ferrules and old straps are pulled, not cut off flush, so they cannot back out later and catch on the new system.
All of the old metal, downspouts and fasteners go on our truck. You are not left with a pile of bent gutter behind the garage, and the yard gets a magnet sweep for nails and screws before we leave.
What we find under old gutters
The fascia behind a failing gutter is often in worse shape than the gutter. Years of drips at a leaking joint soften the board, and a gutter hung with spikes may only be holding on by a few inches of good wood. We probe every run once the old metal is off.
Soft sections are cut out and replaced before the new gutter goes up, and the board can be wrapped in aluminum trim coil to protect it. Our fascia board replacement page covers that work in detail. Hanging new gutters on rotted wood would only bring us back in a year.
Upsizing and rethinking the downspouts
Replacement is the moment to change sizes. Many older houses were built with 4-inch or narrow 5-inch gutters and 2x3 downspouts, and later roof work, additions or steeper dormers have pushed more water into them than they were ever meant to carry. Going to 6-inch gutters on the worst runs is common.
We also look at where downspouts land. Moving an outlet away from a window well or adding a second downspout to a long run costs little during a replacement and saves trouble for years. New downspouts are matched to the gutter color, and extensions are set so water clears the foundation.
Same-day replacement for most homes
A typical ranch or two-story in the metro is torn off, repaired and rehung in one working day. The roll former on our truck forms each new run to length right there, so there is no waiting on parts or ordering custom pieces for odd eave lengths.
Bigger jobs take longer. Houses with extensive fascia rot, steep upper roofs that need extra safety setup, or long commercial-style runs may need a second day, and we will say so when we measure.
What to look for
When replacement beats another repair
Rust coming through
Orange stains on the outside face or pinholes you can see daylight through mean steel gutters are failing from the inside and will keep opening new holes.
Leaks at many seams
If water drips from most of the splices in a sectional system, resealing one joint at a time costs more over a few years than replacing the run.
Repeated sagging
Runs that sag again soon after being re-hung usually point to rotted fascia or failing spikes, both of which are fixed properly during a full replacement.
Wrong size for the roof
Water pouring over the front edge in ordinary storms, even when the gutter is clean, means the system cannot carry what the roof sends it.
Mismatched patchwork
Gutters with sections of different colors, profiles and ages pieced together over the years rarely share the same pitch and rarely drain well.
Siding or roof work planned
When a roof or siding job is coming, replacing tired gutters at the same time avoids taking down and rehanging metal that is near the end anyway.
How the job goes
How a replacement job runs
- 1
Measure and assess
We measure each run, note size, material and condition, check where water lands now, and recommend sizes, outlet locations and any fascia work before you decide.
- 2
Remove the old system
Gutters, downspouts, straps and fasteners come down carefully to protect shingles and siding, and everything goes into our truck for disposal instead of staying on your property.
- 3
Repair the fascia
With the old metal gone, we probe the boards, replace any soft wood, and wrap fascia in trim coil where it makes sense so the new gutters have solid backing.
- 4
Form and hang new runs
New seamless runs are rolled on site, fitted with caps, miters and outlets, then hung on hidden hangers to a string line so each one falls toward its downspout.
- 5
Downspouts and final test
Downspouts and extensions go on, every run is flushed with a hose to confirm the water drains, and the yard is swept for fasteners and metal scraps.
Pricing
Replacement pricing
A replacement combines the price of new gutters with the cost of taking the old ones down. Published removal charges are listed separately below because some sources quote them as a flat add-on and others per foot.
| Item | Published range |
|---|---|
| Full replacement, tear-off included | $12 to $25 per foot |
| Old gutter removal, flat add-on | $50 to $200 |
| Old gutter removal, per-foot add-on | $1 to $2 per foot |
| Fascia board replacement, if needed | $7 to $40 per foot |
| Each new downspout installed | $30 to $75 per downspout |
National ranges published by HomeGuide, Forbes Home, This Old House. Your price depends on the house; we give you a number on the phone or at the house before any work starts. See the full gutter price guide.
The amount of fascia rot found under the old system and any upsizing to 6-inch gutters move the total more than anything else. See our price guide for context.
Omaha conditions
Why so many Omaha gutters are due
Nearly half of Omaha homes were built before 1970, and a large share of those houses are now on their second or third set of gutters, often hung over fascia that has been through many winters of freeze and thaw. Older neighborhoods also tend to have mature trees whose seeds and leaves keep troughs wet, which speeds up rust in steel systems.
Hail is the other driver. The metro logged 88 hail reports within about ten miles of the city in 2024, far more than any other recent year, and dented gutters with cracked seams are a common reason homeowners move straight to replacement. If storm damage is your reason for calling, see our hail damage replacement page.
Talk to a gutter crew about gutter replacement
Tell us what you are seeing at the roof edge. We answer around the clock and give you straight answers on repair or replacement.
FAQ
Gutter Replacement questions
Can new gutters reuse my existing downspouts?
Sometimes, but we rarely recommend it. Old downspouts are often a different color, dented at the elbows, or too narrow for the new system, and an outlet in a new seamless gutter has to line up with the downspout size. Replacing them together costs relatively little and lets us move outlets to better spots. If your downspouts are newer and the right size, we can talk through reusing them.
What happens if the fascia behind my gutters is rotten?
We find out as soon as the old gutters are down, because we probe every board before hanging anything. Soft sections are cut out and replaced with new lumber, and the fascia can be wrapped in aluminum trim coil to protect it from future drips. We explain what we found and what it adds to the job before doing the work, so there are no surprises on the final bill.
Will a gutter replacement damage my roof shingles?
Not when the old system is removed with care. We pull fasteners straight out, lift sections clear of the shingle edge, and avoid prying against the roof. Hidden hangers on the new gutters attach to the fascia below the shingles. If the shingles along the eave are already brittle or the drip edge is missing, we point that out so you can decide whether to address it.
Is it worth upsizing to 6-inch gutters during a replacement?
It is worth it on runs that take water from large roof planes, steep pitches or valleys, and on houses that overflowed even when the old gutters were clean. Not every run needs it, and mixing sizes on one house is fine if the look works. Replacement is the cheapest time to make the change, since the old system is coming down anyway.
Do I need to be home while the gutters are replaced?
Not for most of the day. We need access to all sides of the house, a clear driveway for the truck and roll former, and a working outdoor faucet for the final water test. It helps to be around at the start to confirm downspout locations and colors, and at the end to walk the job with the crew, but many homeowners go to work and come back to a finished house.
Related gutter services
Checking costs? The gutter price guide lists published ranges, the gutter size calculator estimates 5 or 6 inch and downspout count, and the cleaning schedule planner shows how often your trees fill the gutters.